Welcome toHenan Pinzhong Machinery Manufacturing Co., Ltd. !
Current Location: Home > product > Waste treatment equipment series > Views
Waste treatment equipment series

Dryer

Drying machine is mainly used for drying a certain humidity within the scope of the particulate material, such as the dry sand used in the industry of yellow sand, casting industry for a variety of sand, building materials and cement industry with blast furnace slag, small particle size clay, the chemical industry can not afford Chemical changes, not afraid of high temperature and dust particles of small particles of dirt.

Tel:+86-0371-56768575
Product description

Dryer Profile:

Drying machine is mainly used for drying a certain humidity within the scope of the particulate material, such as the dry sand used in the industry of yellow sand, casting industry for a variety of sand, building materials and cement industry with blast furnace slag, small particle size clay, the chemical industry can not afford Chemical changes, not afraid of high temperature and dust particles of small particles of dirt. Commonly used in drying sand, river sand, slag, cinder, quartz sand and other materials drying operation. Widely used in building materials, chemicals, casting, wall insulation and other industries, can be adapted to coal, oil, gas and other materials. According to the requirements of different industries on the final moisture content of the dried material, the moisture content of the dried material can reach below 1.5%. Into the dryer inside the material to non-stick cylinder wall and Yangban appropriate. Into the dryer heat exchange gas temperature should not be higher than 750 degrees Celsius, if there are special requirements of high temperature drying, the dryer at the entrance of the inner cylinder and lifting plate available heat-resistant plate manufacturing.

Dryer construction:

1, the cylinder; 2, the front roller ring; 3, the rear roller ring; 4, the gear; 5, retaining roller; 6, drag roller; 7, pinion gear 8; discharge part; Machine; 11, motor; 12, feed chute (optional); 13, hot air duct (optional); 14, furnace (optional) and other components. In addition, our company can design gas furnace, combustion chamber or supporting hoist, belt conveyor, dosing machine, cyclone dust collector, induced draft fan and other related devices according to user needs.

Dryer works:

Material by the belt conveyor or bucket elevator to the hopper, and then through the hopper feeding machine through the feeding pipe into the feeding end. The slope of the feed pipe is greater than the natural inclination of the material so that the material flows smoothly into the dryer. The dryer cylinder is a rotating cylinder that is slightly tilted from the horizontal. The material is added from the higher end, the heating medium enters from the low end, comes into countercurrent contact with the material, and the heating medium and the material flow into the cylinder together. As the cylinder rotates the material is gravitationally operated to the lower end. During the forward movement of the wet material in the cylinder body, the heating of the heating medium is obtained directly or indirectly, so that the wet material can be dried, and then sent out by a belt conveyor or a screw conveyor at the discharge end. In the dryer cylinder wall with a copy board, its role is to copy and sow the material, the material and airflow contact surface increases, in order to improve the drying rate and to promote the material forward. Heating medium is generally divided into hot air, flue gas and so on. After the heat medium through the dryer, the general need cyclone dust trapped within the material captured. For further reduction of tail gas dust content, but also through the bag filter or wet dust collector and then discharge.

Dryer product advantages:

1, Our company dryer wear plate manufacturing, wear-resistant than ordinary steel 3-4 times.

2, the initial moisture content of 15% of the material, the final moisture to ensure that 0.5-1%, the cement plant slag powder, dry mortar production line and other drying products of choice.

3, Than the traditional dryer to improve thermal efficiency of more than 40%.

4, the fuel can be adapted to white coal, bituminous coal, coal gangue, oil, steam. Can bake 20-40 following block, pellet, powder material.

5, than other drying to reduce the footprint of about 50%. The construction investment in land is obviously reduced.

6, no leakage, completely solve the sealing difficulties.

7, the material temperature ≤ 60 degrees, can be directly into the library, without cooling into the shed.

8, the outer cylinder temperature ≤ 60 degrees, the exhaust temperature <120 degrees, dust bag equipment used more than 2 times longer. Consumption of coal is traditional drying machine 1/3, saving 40%, tons of standard coal consumption <9 kg.

Technical Parameters

Specification

(M)

Cylinder volume

(M3)

Speed (r / min)


Production capacity

(T / h)

Installation slope

(%)

The maximum inlet temperature

(° C)

Main motor

(Kw)


Reducer models



Reducer speed ratio


total weight

(T)

Φ1.2×8.0

9.0

3-8

1.9-2.4

3-5

700-800

7.5

ZL50-16-I

25

9

Φ1.2×10

11.3

3-8

2.4-3.0

3-5

700-800

7.5

ZL50-16-I

25

11

Φ1.5×12

21.2

2-6

4.5-5.7

3-5

700-800

15

JZQ500-III-2F

23.34

18.5

Φ1.5×14

24.7

2-6

5.3-6.6

3-5

700-800

15

JZQ500-III-2F

23.34

19.7

Φ1.5×15

26.5

2-6

5.7-7.1

3-5

700-800

15

JZQ500-III-2F

23.34

20.5

Φ1.8×12

30.5

2-6

6.5-8.1

3-5

700-800

18.5

ZQ50-16II-2

16.46

21.5

Φ1.8×14

35.6

2-6

7.6-9.5

3-5

700-800

18.5

ZQ50-16II-2

16.46

23

Φ2.2×12

45.6

1.5-6

9.7-12.2

3-5

700-800

22

JZQ650-III

31.5

33.5

Φ2.2×14

53.2

1.5-6

11.4-14.2

3-5

700-800

22

JZQ650-III

31.5

36

Φ2.2×16

60.8

1.5-6

13.0-16.2

3-5

700-800

22

JZQ750-III

31.5

38

Φ2.4×14

63.3

1.5-6

13.5-16.9

3-5

700-800

37

JZQ750-III

31.5

45

Φ2.4×18

81.4

1.5-6

17.4-21.7

3-5

700-800

37

JZQ750-III

31.5

49

Φ2.4×20

90.4

1.5-6

19.3-24.1

3-5

700-800

45

ZL85-13-I

27.16

54

Φ2.4×22

99.5

1.5-4

21.2-26.5

3-5

700-800

45

ZL85-13-I

27.16

58

Φ2.6×24

127.4

1.5-4

27.2-34.0

3-5

700-800

55

ZL85-13-I

27.16

73

Φ3.0×20

141.3

1.5-4

30.1-37.7

3-5

700-800

75

ZL100-16-I

41.52

85

Φ3.0×25

176.6

1.5-4

37.7-47.1

3-5

700-800

75

ZL100-16-I

41.52

95

Φ3.2×25

201

1-3

42.9-53.6

3-5

700-800

90

ZL115-16-I

41.52

110

Φ3.6×28

285

1-3

60.8-76.0

3-5

700-800

160

ZL130-16-I

41.52

135

Customer case
Contact Us
Henan Pinzhong Machinery Manufacturing Co., Ltd. Address:188 Datang Road,Gongyi City,Henan Province,China
Phone:+86-0371-56768575 +86-15038099034

Website:http://www.hnpinzhong.com